By Darius Van Rhuehl
Musician’s Friend Staff Writer

Normally when I write a hands-on review, I try to come up with some clever and engaging introduction. With Acoustimax, I think it’s more clever to simply come to the point, since there’s a lot to talk about and limited space to do so. Just as the name implies, Acoustimax is a preamp designed to help you make the very most of the sound of your acoustic-electric guitar—and the name BBE is synonymous with getting the most out of sound.

Accoutrements to the max

Looking at the Acoustimax, it’s pretty clear that its design is born of real-world studio and stage experience, and is equally suited to both. The ground-lift and phase-reverse switches alone are indicators, but so are the -12dB pad and the Pre/Post switch that lets you bypass the master volume control. (More about that later.)

As long as we’re talking about back-panel residents, you’ll also find a dedicated 1/4" tuner output, 1/4" line out, and 1/4" TRS EFX loop (you’ll need a TRS-TS/TS cable for EFX). There’s also a balanced XLR DI out, which is where the Pre/Post switch comes in. When using the DI out, “Pre” lets you bypass the main volume control and “Post” lets you use master volume as a level controller if your output signal is too hot. The pad also can be used to tame hot signals from the DI output.

On the top panel, starting from left to right, there’s Gain, EQ with high- and low-shelving and sweepable mids, a notch filter with -12dB cut from 70-250Hz (to prevent feedback), BBE’s Sonic Maximizer with Process and Lo Contour controls, a master volume control, and two LED clip indicators for input and output overload. The Acoustimax also has a 1/4" TS input on the right side panel and a 1/4" TS output on the left, so it can sit nicely in your pedal array. Footswitches include mute (which really came in handy during my tests) and on/off for the Sonic Maximizer.

Maxing it out

I first tested sound quality, putting it up against three other preamps ranging in price from $650 to $2,250. Did the BBE hold its own? Yes. It didn’t sound better than the boutique pre, but considering the under-$200 price tag, coming in second behind a $2,000 preamp and ahead of a $1,000 one is pretty impressive. Of course, what really put it over the top was the Sonic Maximizer. You can’t get that out of any pre except this one. I also used another of my personal analog favorites with the Acoustimax, a BBE Mind Bender chorus/vibrato pedal in the EFX loop, which gave me a beautiful, larger-than-life sound that was further enhanced by a shimmering high register, courtesy of the built-in Sonic Maximizer.

Mixing to the Max

Since the Acoustimax has three outputs, I was curious if you could send signal simultaneously out of all three. Short answer—you can. If you’re a solo acoustic player that wants to fill the club with sound, you can send signal to two amps onstage plus the house PA system. The balanced DI allows long cable runs without noise or signal degradation, and the ground-lift switch should solve any noise or hums from ground loops.

In the studio, I sent the DI into my favorite tube DI, the line out to the aforementioned boutique preamp, and the normal output direct into my audio interface. Using the phase switch to make sure that all three systems were in phase, I recorded the three inputs to one track. Did I get a 10' acoustic guitar? Oh yeah. Now imagine that accompanying a singer-guitarist, or double-tracked and blended with heavy distorted guitars for a positively huge chorus.

Speaking of blending the acoustic with distorted guitars, here’s where the Sonic Maximizer comes in handy. Since the acoustic guitar has such a full-bodied sound, which will fight the distorted guitars for space, we need to find ways to make it fit in the mix. Some engineers filter out the low mids of the guitar, often brutally chopping everything below 350Hz, where the body of the guitar lives. By itself, the guitar sounds awful; however, it does fit better in the mix. Then there’s another way to go. Use an enhancer, which makes more room in a mix than EQ. Enhancers bring out highs without the harshness of EQ; but overused, they can sound awful. The best solution I’ve come across is the AcousticMax’s Sonic Maximizer. The Process control lets you dial in sparkling, phase-aligned highs, and its Lo Contour control can tame those nasty lows without using drastic EQ—perfect for blending an acoustic guitar in a busy mix.

Side note: If you’re not convinced that the Maximizer is, in fact, a secret weapon of platinum producers, I recently sat in on a session run by a producer with 80 million albums sold. (Sorry I can’t mention names.) He had at least $20K worth of gear on his stereo bus, but sitting in the chain, right between a classic EMI EQ used at Abbey Road and another “legendary” EQ (whose name is also three initials, starting with A and ending with PI), sat the BBE Sonic Maximizer. We listened to the mix with the unit bypassed and engaged. The difference was astounding.

Max is, well . . . smart

The Acoustimax represents a great leap forward in amplifying the acoustic-electric guitar. Whether you want your acoustic to sit perfectly in a mix or take center stage with authority, the Acoustimax gives you all the tools to make it happen. I’d say the Sonic Maximizer alone is worth the price of admission, but perhaps the most important reason to own an Acoustimax is to get back the sound quality lost by running acoustic guitars through PA systems and amps. A fingerstyle soloist shouldn’t even consider going onstage without one. And its value as a creative recording tool is also quite clear. In fact, “quite clear” is what your acoustic-electric should be—and will be, with an Acoustimax taking point in your signal chain. Beyond that, it can take an ordinary acoustic sound and make it extraordinary.

Features & Specs


  • Built-in Sonic Maximizer
  • 3-band EQ with sweepable-mids, LF notch filter
  • Phase reversal
  • Ground lift
  • Line level out
  • Dedicated tuner out
  • TRS effects loop
  • Pre/post switchable DI output with -12dB pad
  • Hardwire bypass
  • Non-slip rubber bottom
  • 12V power supply
  • Frequency Response: 50Hz-20kHz
  • Treble: ±12dB @ 10kHz
  • Mid: ±12dB @ 400Hz-2.5kHz
  • Bass: ±12dB @ 60Hz
  • Notch: 0 to -12dB @ 70Hz-250kHz

Once you hear what the Acoustimax can do for your guitar, you won’t want to play another note without it. Order yours from Musician's Friend and get the benefit of our 45-Day Double Satisfaction and Lowest Price guarantees.


By Darius Van Rhuehl
Musician’s Friend Staff Writer

Finally, a DAW front end from T.C.—now my Finalizer can go back to the end of my recording chain on the stereo bus where it was originally intended. You see, a few years ago I bought the T.C. Electronic Finalizer Plus for mastering, but discovered that its converters sounded better than the dedicated ones I had unfortunately purchased for my DAW front end. So, rather than sitting on the stereo master bus, it’s been the front end of my DAW. Now with T.C.’s Konnekt series of audio interfaces, I can have T.C. sound quality at both ends of my signal chain. So can you.

On your 6

Because T.C. makes gear used at the highest levels of the music and film industry, you’re going to find professional touches in their budget-priced, 24-bit/192kHz FireWire Konnekt 6 that you won’t find in most units built for home recording. For example, the Dim switch, which brings down the level of the mains (adjustable via software), is handy for monitoring at low levels or talkback with an artist. Even its metering is more than the usual eye-candy you find on other interfaces. A high-resolution, 12-segment LED meter, it can operate in three modes: input, output, and mastering. It also enables you to set hold time and fall time. Plus, within easy reach, you have a big volume knob with LED level indicators. You’ll really appreciate this one (as will your neighbors) if you’ve ever accidentally blasted unmuted signals through powered monitors.

Another issue that T.C. has admirably addressed, which has proved to be annoying on other interfaces, is the software control panel that provides channel faders, sends, metering, panning, reverb controls, and more. The 6 has a hardware button that hides or brings up the panel, so you can make your adjustments without having to play whack-a-mole with host software edit and mix windows.

Pro sound quality is courtesy of T.C.’s highly respected IMPACT preamp, which offers crystal-clear, transparent, and spacious sound. And phantom power lets you use a high-quality condenser mic. Don’t get me wrong, just because a preamp has phantom power doesn’t mean that you can use any professional mic. For example, I’ve heard people complain that their Shure SM7 (which Bruce Swedien used for vocals on Michael Jackson’s Thriller) couldn’t be heard through their desktop interfaces. That’s to be expected. The SM7 is a low-sensitivity dynamic mic that puts out a very low voltage (phantom power isn’t going to help you here). The type of preamp you find in most desktop interfaces simply won’t have enough muscle to do the required lifting. That’s where the 6’s 12dB boost switch comes in, so no mic is off-limits.

Yet another pro bonus is the collection of M40 Studio reverbs. You can use them for a vocal cue mix without printing to disk, or as VST/AU compatible plug-ins for mixing. Keep in mind that T.C.’s reverb algorithms are among the very best, and the reverb found on the Konnekt 6 sounds like high-end hardware reverbs. I tell you that from first-hand experience. I’ve worked in studios that use T.C. gear and I know what it sounds like.

T.C. has also done considerable thinking outside the box. For example, what happens when you outgrow your 6 and need more I/O? Rather than taking a hit on your present interface, T.C. NEAR compatibility lets the 6 work with any other Konnekt series interface. So, you really are adding I/O and not trading off, since T.C. doesn’t cut corners on their preamps and conversion. In fact, the 6 includes the same digital clocking and jitter elimination as their industry-benchmark M 6000 hardware processors.

The right Konnektions

The Konnekt 6 is arranged like a mini mixer/master section of a console. On the rear panel, you have one XLR input and two 1/4" inputs that can function as separate instrument DIs or as a stereo pair. There are also balanced 1/4" stereo outputs. On its rather attractive top panel (okay, not as hot as Cylon Number 6, but attractive nonetheless), you have hands-on control of input gain, reverb level, input monitoring, and three scene buttons, that are of particular interest. Scene 1 selects the mic and an instrument input, Scene 2 selects dual instruments and handles them as individual signals, with separate gain controls. This scene is particularly useful if you want to record guitar and bass simultaneously. And finally, Scene 3 is good for a stereo signal, such as a keyboard. The beauty of this setup is that you don’t have to change instrument routing. You can leave your microphone and instruments connected to the three recording inputs and select among them using the scene buttons.

Normally, I have fear and loathing when it comes to installing software on my computer, especially when it fills my hard drive with useless stuff. Installing the software for the Konnekt 6 was as simple and painless as could be. In fact, during the installation, the professional thinking inherent in the 6 becomes apparent. Rather than loading your hard drive with software for units you won’t be using, the Konnekt’s installation window tells you what is mandatory and lets you select only the Konnekt model you have.

Once set up, I found that Logic Pro had no problem finding the 6. However, I felt that it integrated better with the included Cubase LE software. In fact, having used all the major DAWs professionally, I’ve settled on Cubase 4 as my main platform. That said, the sound quality of the 6 was undeniably stellar. The available controls certainly streamlined the recording process, particularly the panel switch and scene buttons. (If T.C. decides to make a pro-level control surface-interface, they can put me down for one right now.)

I want to 6 you up

If you want top-quality sound but don’t want to pay for inputs you’ll never use, the Konnekt 6 is your answer. Plus, it incorporates features and functionality that has quite frankly been missing from much more expensive interfaces. More to the point, T.C.’s converters are among the best out there, and anytime you can have T.C. as your DAW front end, I suggest you do so. The addition of T.C.’s studio-quality reverbs is certainly icing on the cake (and we’re talking the really good icing, not that buttery-flavored stuff), but even more appealing is the ease with which you can get around on this unit, and how much functionality they’ve packed into its tiny and very attractive form. Think about it: a budget-priced interface with pro features and sound born of world-class studio technology—how can you go wrong with that? Short answer: You can’t.

Features & Specs


  • Big volume control knob
  • High-resolution meter
  • Tracking reverb level control
  • Direct monitor control with input/DAW control
  • DIM switch for convenient speaker dimming
  • Instant scene recall
  • IMPACT mic preamp with 48V phantom power
  • 24-bit/192kHz sampling rate
  • Balanced stereo outputs
  • True Hi-Z guitar inputs from T.C.’s high-end guitar processors
  • Headphone out with separate level control and source
  • Studio-quality reverb
  • Reverb available for monitoring or mixing as VST or AU-compatible plug-in
  • Hall, Room, and Plate algorithms
  • T.C. NEAR compatible: works with all other Konnekt products
  • FireWire 1394, bus powered
  • DICE digital interface chip
  • JetPLL jitter-elimination technology
  • Low-latency drivers for Mac and PC, WDM, ASIO, and CoreAudio
  • Cubase LE4 included



Maaf Buat Temen-temen Yang sering ngunjungin blog ni, isinya ga update2, itu dikarenakan kesibukan saya beberapa bulan yang lalu, tapi akhirnya saya bisa memposting kembali info2 musik untuk teman2.....
Drum Set Up The studio dimensions of Disc Ltd. is a 35 x 20 room with wood flooring and medium acoustics. Bass traps line the longer walls at the top to reduce room boom and to even out the bass in the room reverberation. We set up the drums along one of the longer walls with professional 6-foot sound absorbing baffles behind the drummer. Having the drums in the main studio gives a mild amount of reverberation to the sound and using the baffles assures a high degree of presence to the sound.

Input #1 - The Foot Drum

Microphone Selection I selected an Electrovoice RE-20 microphone. This is a large diameter dynamic microphone that has variable D ports. The large diameter diaphragm assures that the mic picks up all of the low-end generated by the foot. The variable-D ports assure that you get a smooth, natural sounding low end. The microphone has smooth frequency response to the highest audio frequencies and therefore will capture the "snap" of the foot also.

Alternate Microphones I would have preferred a RE-27 microphone which is similar to the RE-20 but with a lower-weight diaphragm and coil assembly, giving it a truer sound. Microphones that I would be happy with in a pinch are the Shure Beta 57, the Senheiser MD-421, the Shure SM-57. I would not have been happy to use an AKG D-112 which a lot of people use but sounds like s**t. I would have been unhappy with any kind of condenser microphone which would have a "restricted, cardboard-like" sound - even the best condenser mics have this characteristic. I could have used a good ribbon microphone.

Microphone Placement I like maximum "skin tone" of the foot drum so I almost always place the microphone at the outer diameter of the drum. In the middle, you get more low-end thud but few of the harmonic frequencies that are being generated by the skin.

To get all of the shell sound, I place the microphone diaphragm even with the back of the shell. This means I get both the shell and the skin tine. I usually place the microphone at the top of the drums so that any pillow or blanket used by the drummer does not muffle the microphone pickup.

Microphone Equalization & Sound Check
The equalization I used is as follows

Setting

Purpose

+ 9 dB @ 50 Hz, Shelf Response

Gives the drum good low-end push. The amount should be an amount that causes a slight increase in level when you put the equalizer in the channel.

- 6 dB @ 400 Hz, peak response with Q=1.5

Reduces the cardboard sound and increases foot drum / bass guitar clarity.

+ 4 dB @ 4000 Hz, peak response with Q=1.5

To add sufficient hard beater sound

I brought up the level so that the peaks of the foot drum caused the tape machine's meters to read +3.0. You can overdrive low-frequency instruments on analog tape and they sound better because of this Generally for analog recording I equalize the drums before the sound is recorded on tape. If this was a digital recording I would record without equalization and use thse kinds of EQ settings during the mixdown.

Mixing The Foot Drum The foot drum is the sound in the production that I start with. After I set the foot drum, I pretty much leave it alone, mixing the levels of other drum and rhythm parts to be correct with the foot at a fixed level.

Since I equalized before recording, I don't do much equalization during mixdown. I add a slight amount of plate reverb with a very short reverb time (1/2 of a second) which helps make the drum sound like it's part of the drum kit rather than sitting in your lap. [See snare drum description for reverb parameters.

Input #2, #3 - The Snare Drum

Microphone Placement Approach
I used two microphones to pick up the snare. One microphone is on top of the snare and one is on the bottom. Since I am "micing in pairs" of microphones, I want to have both mics be the same model of microphone. I particularly like the resultant sound for analog recording. If you mic the top of the snare only you will usually have to use EQ to get the snare to sound right. With two microphones, its a matter of blending levels.

Microphone Selection
I selected my favorite dynamic microphone, the Shure Beta-57. This mic has a very true hypercardioid pickup pattern (that stays the same at all frequencies) which allows you to properly reject the high hat from the microphone's pickup. The moving mechanism of the microphone (the diaphragm and coil) are 1/2 the weight of the older SM-57 and therefore the Beta version does a much better job of capturing the transient.

Alternate Microphones
I would have preferred a ribbon microphone like the Beyer 500 series (or even the 260 series), because ribbons would get a clearer attack. A set of condenser microphones like AKG 414 would have sounded good but there would be less high hat rejection (the pattern is not as true for all frequencies on the 414). Other microphones that I would be happy with in a pinch are the EV RE 15 the Senheiser MD-421. I would not have been happy to use an SM-57 or SM-58 because of a muffled sound due to the transient not being picked up properly and because of increased leakage (because these microphones' pickup patterns vary with frequency).

Microphone Placement
I put the microphone at the edge of skin and angle the back so that the rejection of the microphone points at the high hat. For the bottom microphone, I make a "mirror image" of the top microphone. If I were using the MD-421 microphone I would turn on the bass roll-off. With the 414 microphone I would both turn on the microphone pad an the bass roll-off.

Microphone Routing, Equalization & Sound Check
I activate the phase-reverse on the console channel that I am using for the bottom snare microphone. If the two microphones are mixed together without a phase-reversal, the snare will "thin out" because of phase cancellation of the lower frequencies generated by the drum. I like to phase reverse when I cut so that the multitrack mater can just be mixed. I like to record onto two tracks and blend the two microphones later during mixdown. I always note on the log sheet for the reel, "Sn Bottom" and put a phase-reverse sign after the words.

Often I will avoid equalization during recording but sometimes a slight increase of presence or treble is needed to get the right amount of snap. I always equalize the top and bottom snare channels at the same frequency but I usually use peak EQ on the top microphone and shelf EQ on the lower microphone. This is because the snares on the bottom of the drum generate more high-frequency energy.

Setting

Purpose

+ 4.5 dB @ 7000 Hz, Shelf Response

For bottom snare. To increase "attack" of snare drum.

+ 4.5 dB @ 7000 Hz, Peak Response, with Q=2.0

For top snare. To increase "attack" of snare drum.

I brought up the level so that the peaks of the snare drum top mic caused the tape machine's meters to read +0.0; and brought up the level of the snare drum bottom mic to cause the tape machine's meters to read -3.0. You can overload an analog tape machine track easily if the pickup of the microphone is all high-frequency percussive energy - this is why the bottom microphone signal is recorded at a lower level.

Mixing The Snare Drum
The top snare track is used to establish the general level of the snare in the mix - usually equal to the foot drum level by ear. I bring up the bottom snare track until there is enough snap.

For the drum mix, I will have three reverbs activated (see last week's tip). On the top snare I will blend the shortest reverb with the medium reverb. For the bottom snare, I usually only use the shorter reverb. I pan both tracks center. The chart below lists the programs use and suitable substitute programs I could have used.

PROGRAM FUNCTION SETTINGS SUBSTITUTE SETTINGS NOTE
PLATE Attack
Predelay: 0.0
Rev Time: 0.5 sec
GATED
Predelay: 0.0
Rev Time: stock

provide s attack/snap to the reverb

HALL Hall
Predelay: 18 ms
Rev Time: 1.8 sec
NONE

provides good-sounding natural ring out

PLATE Room
Predelay: 10 ms.
Rev Time: 1.5 sec
ROOM
Predelay: 5 ms.
Resizev Time: 1.5 sec
smoothes transition between programs - makes reverb denser

Input #4 - The High Hat

Microphone Selection
I selected a 414 large-diameter condenser microphone. I activated maximum bass roll-off and put the pad to "-10". I put the microphone on hyper-cardioid. The biggest factor that caused me to choose this microphone was the availability of the hypercardioid pattern.

Alternate Microphones
I could have used any condenser microphone that had bass roll-off and a pad. I would not have used any dynamic microphone, because the high quick transients put out by the high hat would have been muffled by the best dynamic microphone. I could have used a good ribbon microphone with a figure-8 pattern (bidirectional), which rejects the snare drum better.

Microphone Placement
I put the microphone about 8 inches away from the high hat and kept the cymbal between the microphone and the snare drum. Sometimes too much snare can get into the high hat mic and pointing it out away from the snare helps, as does the hypercardioid pattern. I made sure that the axis of the microphone was in line with the axis of rotation of the cymbal. I turn the bass roll-off switch to maximum and turn on the microphone pad.

Microphone Routing, Equalization & Sound Check
I will often add a slight amount of extreme highs to accent the "sizzle" of the high hat.

Setting

Purpose

+ 4.5 dB @ 12,000 Hz, Shelf Response

For increased sizzle of the cymbal

-6.0 dB @ 200 Hz, Shelf Response

To reduce snare drum pickup as well as reducing ambience.

I brought up the level so that the peaks of the high hat read "-6" on the console's output meter. The high hat is all high end and will overload analog tape at "0" level.

Mixing The High Hat
I mix in the high hat after I bring up the foot and snare drum. I usually pan the high hat right and slowly bring up the high hat fader. When the image shifts right, this is a good level. Even with no high hat track in the mix, you will hear high hat through the leakage into the center-panned snare mic. When the high hat track gets present enough in the mix you will hear the high hat shift to the right.

For the drum mix, I use the shortest reverb on the high hat track.

Inputs #5. #6 & #7 - The Toms

Microphone Selection
I selected the Shure Beta-57 microphones to pick up the toms. The biggest factor that caused me to choose this microphone was the true hypercardioid pattern and how even the rejection is at all frequencies.

Alternate Microphones
I could have used the senheiser MD-421, or any high-quality dynamic microphone with a "true" pickup pattern. I could have used a good ribbon microphone.

Microphone Placement
I put the microphone on the toms much as I place the top microphone of the snare. I point the rejection of the microphones towards the nearest cymbal. The microphone is about a quarter-inch away from the drum skin at the edge of the skin.

Microphone Routing, Equalization & Sound Check
I routed the toms to two tracks using two busses (4&5). All three inputs were routed to both busses, and the pan pots associated with the routing matrix, allowed me to pan the smallest tom (#1) fully-right, tom 2 in the center and tom 3 (the floor tom) fully-left. The toms are panned according to the audience perspective but made more extremely panned then how the drum image would be if heard live.

I will often EQ the toms much as I do for the foot drum. I boost the smallest tom at a slight higher bass frequency because, compared to the other toms, it generates less very low frequency energy because of its smaller size.

Setting

Purpose

+ 9 dB @ 50 Hz, Shelf Response

(Use 80 Hz for smallest tom)

Gives the drum good low-end push. The amount should be never be an amount that causes more than a slight increase (2-3 dB) in level when you put the equalizer in the channel.

- 6 dB @ 400 Hz, Peak Response with Q=1.5

Reduces the cardboard sound and increases drum/guitar clarity.

+ 4 dB @ 7000 Hz, Peak Response with Q=2.0

To add a metallic attack to the toms.

I brought up the level so that the louder hits for tom 1 & 3 read "0" on one of the console's output meters. The middle tom should read "-3" on both the Left and right meters.

Mixing The Toms
I mix in the toms after the foot snare drum and high hat. I pan the two tom tracks left & right and slowly bring up the faders. There will come a point that I notice an increase in room ambience - at this point I reduce level slightly (2-3 dB). I make final level adjustments when I hear the tom rolls For the mix, I use the a combination of room and hall reverb on the toms.

Inputs #8 & #9 - The Overhead Cymbals

Microphone Selection
I selected two Crown C700 condenser microphones. These microphones are primarily used for picking up the cymbals and the small diameter head on this microphone does the most accurate job of doing this.

Alternate Microphones
I could have used any condenser microphone. If I had used a microphone without a bass roll-off feature, I would attenuate the bass with a filter on the console. I would not have used any dynamic microphone, because the high quick transients put out by the crash and ride cymbals would have been muffled by the best dynamic microphone. I could have used a good ribbon microphone.

Microphone Placement
I put the microphone pair slightly higher than the highest cymbal and use a 120 degree angle between the microphones (a "wide" XY configuration). The more severe angle and the proximity of the pair to the cymbals increases the cymbal pickup and reduces the level of the snare drum

Microphone Routing, Equalization & Sound Check
I will often add a slight amount of extreme highs to accent the "sizzle" and presence of the cymbals.

Setting

Purpose

+ 4.5 dB @ 10,000 Hz, Shelf Response

For increased sizzle and presence of the cymbal

-6.0 dB @ 200 Hz, Shelf Response

To reduce tom & foot drum pickup as well as reducing ambience.

I brought up the level so that the peaks of level reach "0" on the console's output meters. You will usually get the maximum level when there is a tom roll and a lower level )around "-6" on crashes.

Mixing The Overhead Cymbals
I mix in the overheads after the rest of the drums are in the mix. I listen to the overall drum tone change as I increase the level - in particular how the snare drum sounds will alter. Besides giving presence and volume to the cymbals, these tracks will tend to increase the attack on the snare drum and the toms.

For the drum mix, I use the attack reverb and a slight amount of room reverb.

DRUM MIXING - Reverb Notes

What's Reverb like today? An engineer of ours told me a few weeks ago that there was less reverb in mixes today compared to those of say 10 years ago. One of my recording instructors had talked about this also. I told Chaz (the engineer) that I thought he was full of s**t and there was every bit as much reverb being used today.

We met with gloves on in the mastering room (with the truest monitor speakers in the building) and listened. Chaz is occasionally a recording instructor for RID and has a choice collection of current R&B always with him. I wanted to see what changes in reverb there actually were in this idiom.

After several CD cuts were played, we pretty much agreed with the changes but had different ways of describing the changes in reverb sound for the 21st Century. Gone in today's mix of today is the long-tail reverb of last decade, and if it was present it was in very restricted amounts. There is every bit as much reverb in the mixes but shorter reverb that often is more of the instrument's sound than of room effect added later.

So What Does One Do Differently? The stock programs in effects units usually have factory presets like the reverb used a decade ago. There are two time parameters that are usually "out of whack" for today's mixing.

PARAMETER

DESCRIPTION

PRE DELAY Also known as initial delay, which is the length of time that the reverb takes to build up after the direct sound occurs.
REVERB TIME How long, in seconds, that it takes for the reverb to die away.

So the first thing to be done to your hall programs is to cut the time parameters listed above in half. This means the reverb is established twice as fast and dies down twice as fast. Room and chamber programs need the reverb time parameters reduced by 25% to 50%. These few changes in parameter settings make reverb more like today's reverb sound.

In setting up the reverb for mixing the Giftvs drums, the following changes were done from stock settings:
PROGRAM FUNCTION SETTINGS ORIG SETTINGS
PLATE Attack
Predelay: 0.0
Rev Time: 0.5 sec
Predelay: 0.0
Rev Time: 1.8 sec.
HALL Hall
Predelay: 18 ms
Rev Time: 1.8 sec
Predelay: 24 ms
Rev Time: 2.2 sec
PLATE Room
Predelay: 8-10 ms.
Rev Time: 1.5 sec
Predelay: 0 ms.
Rev Time: 1.8 sec.




Your Ad Here